| HPE Storage Users Group https://3parug.com/ |
|
| 3Par 7200 -Interface Card 0 Failed (Interface Card Firmware https://3parug.com/viewtopic.php?f=18&t=3622 |
Page 1 of 1 |
| Author: | lukehy [ Tue Jul 13, 2021 8:05 am ] |
| Post subject: | 3Par 7200 -Interface Card 0 Failed (Interface Card Firmware |
Hello all. i did showinventory and could only see one node - the other failed. i replaced the Node 0 that was faulty - noticed that the Mgmt was not connected - connected it as well. the node was not added automatically to the cluster and has a solid green light on it. is there a process i need to do after replacing the node ? thank you in advance. |
|
| Author: | MammaGutt [ Tue Jul 13, 2021 9:25 am ] |
| Post subject: | Re: 3Par 7200 -Interface Card 0 Failed (Interface Card Firmw |
lukehy wrote: Hello all. i did showinventory and could only see one node - the other failed. i replaced the Node 0 that was faulty - noticed that the Mgmt was not connected - connected it as well. the node was not added automatically to the cluster and has a solid green light on it. is there a process i need to do after replacing the node ? thank you in advance. That depends on how you replaced it and where you got it. If it was taken from another system it is probably stuck with a different node ID or serial. If you didn't move the node drive, it needs to be rescued. |
|
| Author: | lukehy [ Tue Jul 13, 2021 11:19 am ] | ||
| Post subject: | Re: 3Par 7200 -Interface Card 0 Failed (Interface Card Firmw | ||
Hello. Purchased it online. i connected a serial to the node and received when booting Remote SSN mismatch node 1 expected SSN 18b0ab but got SSN 1934d8” i attached the screenshot as well.
|
|||
| Author: | MammaGutt [ Tue Jul 13, 2021 1:41 pm ] |
| Post subject: | Re: 3Par 7200 -Interface Card 0 Failed (Interface Card Firmw |
Yeah, that is probably a reason. You could try node rescue, I think that might reset the SN.... if not you would have to whack the node to set it (or clear the old one) there. Maybe some hints here : https://www.3parug.com/viewtopic.php?f= ... 5&start=10 |
|
| Author: | lukehy [ Wed Jul 14, 2021 1:43 pm ] |
| Post subject: | Re: 3Par 7200 -Interface Card 0 Failed (Interface Card Firmw |
MammaGutt wrote: Yeah, that is probably a reason. You could try node rescue, I think that might reset the SN.... if not you would have to whack the node to set it (or clear the old one) there. Maybe some hints here : https://www.3parug.com/viewtopic.php?f= ... 5&start=10 Hello. i opened a ticket in HPE support just in case and this was the process reboot the node when it shows grub Ctrl+w that got me into whack prom edit enter till you get to SN change it to the correct one on the node part change it to the right node (0 in my case) reset after that check when booting if new disk go to whack again (Ctrl+w) ide erase when it reboots from the working node run the command startnoderescue -node 0 it suppose to copy and it will join the cluster. hope that this information will help in the future to somebody please let me know if i missed a step or a command. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|