HPE Storage Users Group

A Storage Administrator Community




Post new topic Reply to topic  [ 7 posts ] 
Author Message
 Post subject: ERROR StoreServ Storage Configuration for Server ID 431458
PostPosted: Fri May 02, 2014 7:15 am 

Joined: Fri May 02, 2014 2:36 am
Posts: 3
Hi,

We get a VSS 3PAR provider error when we start a backup of a Windows 2008 R2 SP1 server.
the installed VSS Hardware provider is "HP 3PAR VSS Provider(2.3.0.11)".

EventID: 5078
Source: 3PARVSSProvider
Details: 3PARVSS5078: ERROR: Can not find HP 3PAR StoreServ Storage Configuration for Server ID 431458.

We have created a call at HP. But maybe someone knows the solution


Top
 Profile  
Reply with quote  
 Post subject: Re: ERROR StoreServ Storage Configuration for Server ID 4314
PostPosted: Fri May 02, 2014 4:40 pm 
Site Admin
User avatar

Joined: Tue Aug 18, 2009 10:35 pm
Posts: 1328
Location: Dallas, Texas
I don't have an answer, but in case its helpful here is a direct link to the VSS Provider documentation at HP.

http://h20566.www2.hp.com/portal/site/h ... cachetoken

Looking at page 10 of the user guide... I would first verify that your system is registered properly with VSS, and try re-registering if needed.

_________________
Richard Siemers
The views and opinions expressed are my own and do not necessarily reflect those of my employer.


Top
 Profile  
Reply with quote  
 Post subject: Re: ERROR StoreServ Storage Configuration for Server ID 4314
PostPosted: Tue May 06, 2014 9:43 am 

Joined: Fri May 02, 2014 2:36 am
Posts: 3
Hi, the VSS Provider documentation is not helping. Currently opened a support case at HP.

Keep you posted.


Top
 Profile  
Reply with quote  
 Post subject: Re: ERROR StoreServ Storage Configuration for Server ID 4314
PostPosted: Wed May 07, 2014 11:59 am 

Joined: Wed Aug 07, 2013 3:22 pm
Posts: 254
See the VSS user guide http://goo.gl/EabCln page 30.

5078 Cannot find HP 3PAR StoreServ Storage Configuration for Server ID < StoreServ ID>.

Verify that the StoreServ exists using ProvCfg utility. If StoreServ does not exist, then register the StoreServ and try the operation again.


Top
 Profile  
Reply with quote  
 Post subject: Re: ERROR StoreServ Storage Configuration for Server ID 4314
PostPosted: Tue Jul 22, 2014 3:52 am 

Joined: Fri May 02, 2014 2:36 am
Posts: 3
After a long time not to have heard from HP, Do we have a solution.

VSS Snapshot service looks at the final part of the WWN of the disk. This piece is in newly created disks serial number 3Par.
Because we have our disks migrated from an EVA8400 does not match this.

To correct this, all connected servers should be turned off.
and adjust the respective disks with the command "setvv -WWN car <Disc name>" from the CLI.

After this is done, the VSS provider is working properly.

Though I find this a dirty solution. It works!


Top
 Profile  
Reply with quote  
 Post subject: Re: ERROR StoreServ Storage Configuration for Server ID 4314
PostPosted: Wed Jul 01, 2015 5:00 am 

Joined: Wed Jul 01, 2015 4:54 am
Posts: 1
Check the provider information stored in the application host
C:\Program Files\3par\HWPRV>ProvCfg.exe InServ -sys par002.3parhp.com -detail

if the query is not listing the state consider reconfiguring the array information using this command

C:\Program Files\3par\HWPRV>ProvCfg.exe InServ -sys par002.3parhp.com -user 3Par -pass my3ParPassword -sockssl on

You need to restart the application host after this.

Hope this helps.


Top
 Profile  
Reply with quote  
 Post subject: Re: ERROR StoreServ Storage Configuration for Server ID 4314
PostPosted: Wed Oct 18, 2017 10:32 am 

Joined: Wed Oct 22, 2014 10:22 am
Posts: 7
Although this is an old thread, we hit this issue recently, after migrating volumes from EMC VMAX to 3PAR using Online Import Utility (OIU), and bitwizz's last post hit the nail on the head, albeit it with slight change needed in the setvv command syntax.

For each primary VV in question run:

3PAR01 cli% setvv –wwn auto <VVName>

This will change the VV’s WWN to one based on the source 3PAR S/N.

This scenario is documented in the HPE 3PAR Online Import for HDS Storage white paper (pages 24 and 30); unfortunately, the earlier HPE 3PAR Online Import for EMC Storage white paper did not mention this scenario.

Essentially the HPE 3PAR VSS Provider is doing as it is designed – only allowing you to take snapshots of 3PAR VVs.

Volumes created natively on a 3PAR have the serial number of the array in hexadecimal form in the last five characters of the WWN:

3PAR01 cli% showvv -showcols Id,Name,VV_WWN

Id Name VV_WWN
1222 snap_test 60002AC000000000000004C60001BE8E

3PAR01 cli% showsys

ID ---Name---- ---Model----
0x1BE8E 3PAR01 HP_3PAR 8###

Clearly this isn’t the case with volumes migrated using OIU from an EMC array:

3PAR01 cli% showvv -showcols Id,Name,VV_WWN

Id Name VV_WWN
586 Volume_0157D 60000970000298700262533031353744

With the EMC VV_WWN digits:

  • Digit 0-6 represent the <vendor id>. ('6006048' is the EMC Symmetrix vendor-id, '6000097' is EMC Symmetrix V-MAX vendor-id.)
  • Digit 7-19 represent the <Symmetrix serial number>
  • Digit 20-31 are the <ASCII representation of the Symmetrix device>. The ASCII sequence contains one, two or three ASCII characters followed by the device serial number in ASCII (either 3, 4 , 5 digit device numbers). This is Enginuity dependent.

(see How to decode a Symmetrix device WWN: https://emcservice.force.com/CustomersP ... 0008TZKCA2).

If the host genuinely had storage presented to it from multiple arrays for example, it wouldn’t make much sense for the 3PAR VSS Provider to try and take snapshots of anything else.

OIU has also done as it’s designed – volumes migrated from non-3PAR arrays retain the data they had on the source – and that includes the name, size, WWN and export host data (when migrated as a host).

So it's not a bug, but it clearly is an omission in the OIU documents, as there are some additional steps needed post-migration for hosts which have LUNs which need to use the HPE 3PAR VSS Provider (or any HPE 3PAR Recovery Manager products) for managing snapshots.

Notes on Changing VV WWNs

Changing VV WWNs is disruptive to I/O and requires the volume to be unexported from the host before changing the VV’s WWN.

In addition, this option is not allowed for an admitted volume before it is imported (during Online Import) or whilst the import process is taking place. It can only be run post-migration.

When changing VV WWNs keep the following in mind:

  1. Operating Systems that use the VV WWN as identification may need additional steps to correctly recognise the LUN, once its WWN has changed. For example, VMware uses the NAA..<diskwwid> for multipathing. If the WWID is changed VMware may see the updated VV WWN as a separate volume or snapshot. In this instance the inventory may have to be reimported for the correct operation of cluster DRS.
  2. On clusters which make use of Remote Copy (e.g. with CLX or Peer Persistence) the VV WWN needs to be changed on the Primary/Source VV, and the VV WWN of the target VV on the Secondary/Target Array must be updated to match.
  3. Volumes that are part of a Remote Copy Group cannot have their WWNs updated whilst part of a group. The group must be stopped, volumes removed from the group, have their WWNs updated and then added back into the group, before restarting the group.
  4. For Peer Persistence to function, the (Remote Copy) source and target volumes must have the same WWN. Target volumes created automatically during the Remote Copy Group setup process share the same WWN by default. Volumes created manually during Remote Copy Group setup do not and will need to be updated to match (see steps 2 & 3 above).
  5. Any volume migrated using OIU may need to have their VV WWN updated post-migration to follow 3PAR conventions, in order to use HPE 3PAR Recovery Manager products, including the HPE 3PAR VSS provider.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 7 posts ] 


Who is online

Users browsing this forum: No registered users and 57 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group | DVGFX2 by: Matt