HPE Storage Users Group
https://3parug.com/

3PAR correct remove cage
https://3parug.com/viewtopic.php?f=18&t=2712
Page 1 of 1

Author:  Guktilar [ Thu Nov 09, 2017 6:47 am ]
Post subject:  3PAR correct remove cage

Hello,
I have 3PAR 7400c and two cage M6720.
Service Processor 5.0.2.0-23974, 3PAR OS 3.3.1.215 (GA)+P01,P02,P04,P06,P13,P16
Code:
showcage
=====================================
Id Name  LoopA Pos.A LoopB Pos.B Drives Temp  RevA RevB Model FormFactor
 0 cage0 1:0:1     0 0:0:1     0     16 30-31 4082 4082 DCN1  SFF       
 1 cage1 1:0:2     0 0:0:2     0     12 32-35 4082 4082 DCS1  LFF       
 2 cage2 1:0:1     1 0:0:1     1     23 32-35 4082 4082 DCS1  LFF
I need to remove "cage2". My actions:
- all data deleted on cage2
- all physical disks are deleted using the command "dismisspd"
- all physical disk have status "new"
- trying to remove "cage2"
Code:
servicecage remove cage2
Are you sure you want to run "servicecage remove cage2"?
select q=quit y=yes n=no: y
Remove cage2 failed. It has active ports
And now interesting, i'm trying to offline the ports "1:0:1":
Code:
controlport offline 1:0:1
WARNING: Port 1:0:1 has active disks that may be disrupted.
Are you sure you want to run controlport offline on port 1:0:1?
select q=quit y=yes n=no: y
and "0:0:1":
Code:
controlport offline 0:0:1
WARNING: Port 0:0:1 has active disks that may be disrupted.
Are you sure you want to run controlport offline on port 0:0:1?
select q=quit y=yes n=no: y
Oops! And here the system 3PAR reboots with errors:
lost connection with virtual volume ".srdata" and "admin" who were on "cage0"
Tell me how to correctly remove "cage2".
Thanks!

Author:  MammaGutt [ Thu Nov 09, 2017 7:04 am ]
Post subject:  Re: 3PAR correct remove cage

Look at your showcage and see how cage0 is connected. When you offline 0:0:1 and 1:0:1 you're also cutting off cage0 which contains the FC drives which has the .srdata and admin volumes.

Author:  Guktilar [ Thu Nov 09, 2017 7:09 am ]
Post subject:  Re: 3PAR correct remove cage

MammaGutt wrote:
Look at your showcage and see how cage0 is connected. When you offline 0:0:1 and 1:0:1 you're also cutting off cage0 which contains the FC drives which has the .srdata and admin volumes.

Уes I saw it. How to make that at these ports was connected only "cage2"?
How to correctly remove "cage2"?
Thanks!

Author:  MammaGutt [ Thu Nov 09, 2017 8:56 am ]
Post subject:  Re: 3PAR correct remove cage

I would assume that you need to dismiss all pds in the cage prior to removing the cage.

I haven't done it before so just an assumption based on it complaining about active ports.

Author:  Guktilar [ Tue Nov 14, 2017 11:44 pm ]
Post subject:  Re: 3PAR correct remove cage

Contact HPE support, their recommendations:
- move data from the cage2 (http://3parug.com/viewtopic.php?p=5529)
- "dismisspd" all physical disks in cage2
- turn off the power supply units in cage2
- execute the command "servicecage remove cage2"
- disconnect all cables from cage2
- execute the command "adminhw"
Good luck!

Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/